Netcomm NTC-221-01-01 4G LTE Cat 1 Industrial IoT Failover Router

Netcomm NTC-221-01-01 4G LTE Cat 1 Industrial IoT Failover Router

Availability: Out of stock SKU: NTC-221-01-01

$516.52 (inc. of GST)

Or $103.30 today and more time to pay with

Netcomm NTC-221-01-01 4G LTE Cat 1 Industrial IoT Failover Router

Availability: Out of stock

Description

The 4G LTE Category 1 Industrial IoT Router (NTC-220) is a robust, cost-effective device, designed to bring value to a myriad of applications. Supporting Category 1, the NTC-220 is ideal for the use-case scenarios requiring extended data throughput, yet reliable and highly secure connectivity. Its enhanced remote management and software development capabilities enable to tailor the device to the most unique needs.

What’s in it for you?

  • Cat 1 4G LTE (10Mbps)
  • A Fast Ethernet port, a serial port and a USB port
  • Integrated GPS for reliable asset tracking
  • Software configurable I/O ports
  • Rugged industrial design for harsh environments
  • Ignition sense capability and a wide input voltage range for vehicular applications
PEAK DATA SPEED (MODEL DEPENDENT)
• LTE FDD: Max 10 Mbps (DL) / Max 5 Mbps (UL)
• LTE TDD: Max 8.96 Mbps (DL) / Max 3.1 Mbps (UL)
• DC-HSPA+: Max 42 Mbps (DL) / Max 5.76 Mbps (UL)
• UMTS: Max 384Kbps (DL) / Max 384Kbps (UL)
• EDGE: Max 236.8 Kbps (DL) / Max 236.8 Kbps (UL)
• GPRS: Max 85.6 Kbps (DL) / Max 85.6 Kbps (UL)
ANTENNA CONNECTORS
• 2 x SMA connectors for 4G/3G/2G
(1 x Main and 1 x RX Diversity)
• 1 x SMA connector for GPS
INTERFACES
• 1 x 100Base-T Ethernet RJ45 port
• 1 x RS232 Serial Port DB-9 female DCE supporting either
9 wire RS232 or RS485/RS422 (software selectable)
• Software controlled termination resistors for RS485
• 1 x Micro USB 2.0 OTG interface with 0.5A supply capability
• I/O terminal block providing:
– 3 x Multipurpose I/O pins
– NAMUR (EN 60947-5-6 / IEC 60947-5-6) compatible
sensor input
– Analogue 0V to 30V input
– Digital input (through measurement of voltage above/ below threshold)
– Open collector output
• 1 x Recessed multifunctional reset button
– Reboot
– Reboot into recovery mode
– Reset to factory default settings
LED INDICATORS
• 8 x tri-colour LEDs – Power, Network, a GPS/customizable LED and 5x
Signal Strength indicators
• Easy and clear LED status display for connection status,
connected network type, and connection errorsGPS (MO GPS
GPS
• GLONASS
• BeiDou
• Galileo
• QZSS
SIM CARD READER
• 1 x SIM card slot
– Supports Mini USIM/SIM Format (2FF)
– Optional soldered-down SIM (ETSI MFF2 DFN-8 USIM)
PROCESSOR AND STORAGE
– 800 MHz ARM Cortex A8 processor with 128 MB RAM
– 512 MB flash memory storage CELLULAR
• Profile managed packet data connections
• NAT Disable for framed route configuration
• Transparent bridge mode using PPPoE to allow the router to transparently forward Public WAN IP address to a downstream device
• SIM Security Management (PIN configuration, enable and disable)
• Automatic and manual cellular band selection
• Automatic and manual operator selection
• Odometer reading available via Web-UI, CLI and SDK
NETWORK & ROUTING
• Static Routing, RIP (v1/v2), Port Forwarding and DMZ
• Dynamic DNS
• VRRP for redundant router failover
– DHCP Server including address reservation by MAC address
– Custom DNS server definitions
– DHCP Relay
– DHCP list display in Web-UI
– Advanced DHCP Option configuration (Option 42 NTP,
Option 66 TFTP, Option 150, Option 160)
• Data Stream Manager providing ability to create mappings between input and output ports (e.g. Serial Port, SMS, USB) and perform required translation or data processing by each virtual tunnel.
• Modbus Server TCP/IP Gateway and Client TCP/IP Agent with up to 247 slaves connected to the Serial TCP/IP
Gateway.
• Modbus RTU/ASCII frames support. VPN
• PPTP Client for VPN connectivity to remote PPTP VPN Server
• IPSec tunnel termination (for up to 5 tunnels)
• GRE Tunnelling
• OpenVPN (Client, Server and P2P)
ADMINISTRATION & CONFIGURATION
• Secure web-based user interface (HTTPS) for full device status and configuration
• Password protected configuration file backup and restore for quick device configuration and device cloning
• SSH Command Line Interface for status monitoring, configuration and control
• SNMP v1/v2/v3 including cellular specific MIB, config and firmware download
• TR-069 Client for remote device configuration, configuration backup and restore, and firmware upgrade
• SMS Client (Send/Receive) including inbox, outbox
• Ping monitor watchdog (Reset connection on repeated ping failure)
• Diagnostic Log Viewer (remote and local)
• System Status and Security Logs
• NTP Server Support for network time sync of device’s system clock
• Device User Guide stored on the device and accessible via the secure web-based user interface (HTTPS) Industrial IoT 6
• Advanced Diagnostics and Control via SMS – Query status information – such as Signal Strength,
– Configure device remotely via SMS – such as APN, authentication settings, and many more
• Execute commands via SMS – such as reboot, reset to defaults, go offline, and many more
• Secure SMS management using sender whitelisting and password management
• SMS acknowledgement replies for queries and commands FIRMWARE MANAGEMENT
• Firmware Upgrade locally via LAN or remotely Over-TheAir (HTTPS, SNMP, TR-069, LWM2M)
• Multiple firmware image storage on device and dynamic install
• Triggered firmware upgrade via SMS (initiate download & install from HTTPS)
SOFTWARE DEVELOPMENT KIT
• Develop and install custom software applications
• Open Linux standard development environment
• Develop applications/scripting in standard ANSI C/Shell script and LUA
• Package manager built into Web-UI for Application installation/removal
• API (C, LUA and Shell libraries) to the unit’s internal
Runtime Database to allow full status monitoring configuration and control of the device from custom applications
TEMPERATURE
• Operating Temperature Range: -40°C to +70°C
• Storage Temperature Range: -40°C to +85°C
• Operating Humidity Range: 0-95%
POWER SUPPLY
• Power input via 6-way termination block receptacle
• Field terminable power input via screw type terminal block included
• DC Power (8 - 40V DC)
• 1 x Dedicated ignition input and 3 x I/O ports on 6-way
connector (only available on some models)
• Power consumption 6W, recommended DC supply via
terminal block (12V 1.5A)
• Vehicle compatible protection on DC Input Jack. (ISO7637 standard)
DIMENSIONS, WEIGHT & MOUNTING
• Device dimensions (excluding external antenna): 143 mm
(L) x 107 mm (W) x 34 mm (D) / 221 g (254 g with bracket)
• Wall mount support in multiple orientations via embedded mounting holes
• DIN Rail mount support via plastic bracket included in box
(Top hat section rail TH 35 IEC60715)